Handmade by Diana

Clean and Simple Creations

Ornament Keepsake Tutorial

I finally had time to make the beautiful Ornament on the cover of the 2012 Holiday Catalog. Special thanks to Linda Heller for her insightful tips.

Following is a step by step tutorial on how to put it together. A list of supplies are at the end of this post.

Start by cutting six 3″ x 12″ strips of Very Vanilla card stock. Then stamp 20 of each ornament then run through the Big Shot.

To save time run both dies through the Big Shot at the same time.

Once they are all stamped and cut out. Place them in piles of four.

Fold three of the four ornaments in half.

Then use your bone folder to give it a tighter crease.

Use liquid glue (Tombow), to glue the three creased ornaments together. DO NOT attach to the non-folded ornament.

Using a two-way glue pen, glue around all the edges of the ornament, then add Dazzling Diamonds.  Set aside to let dry.

Next take your Scalloped Cherry Cobbler Tulle Ribbon and cut five pieces at 5.” Approximately three scallops wide.

Punch a 1-3/8″ circle out of card stock. Then glue the top part of the ornament upside down on the circle.

When the Dazzling Diamonds has dried, glue the 3-D ornament to the flat piece.

Using a hot glue gun, take your tulle and insert between each of the ornaments.

Quick Tip:Pinch the tulle in the middle then twist the bottom end then glue the twisted end to the base. The open end should be facing out when attached.

Next cut five pieces of Linen Thread at 12″ each.  To make double loops, fold in half to make 6″ then fold in half again to make 3″ then tie a knot at the bottom.

Next take your loops and lay them down the center of the 3-D ornament, then hot glue the knotted end at the base.

While the hot glue is drying. Take the smaller 3-D ornament and attach to the flat ornament.

Insert the smaller 3-D ornament at an upward angle on top of the tulle (between the green ornament).

Picture1

Using the Rosette Bigz Die, cut a 1″ x 12″ strip of DSP. (I used Be of Good Cheer DSP). Then attach to the center with hot glue. Then hot glue a large Vintage Faceted Designer Button, topped off with a large pearl.

To give it a finished look on the backside, add a sentiment using a 2-1/2″ circle punch and adhere to the back.

Picture2

To make the hanger, punch a 1/8″ hole at the top of the and string through an 8″ piece of Very Vanilla Taffeta Ribbon. Tie a knot at the ends then pull through showing the loop on top.

Your final project. Give it a try, it's easier than you think.

Your final project. Give it a try, it’s easier than you think.

Supplies:Stamps: Ornament Keepsakes

Ink:  Old Olive, Cherry Cobbler

Paper:  Very Vanilla Card stock and scrap card stock for 1-3/8″ circle

Accessories:  Holiday Ornaments Framelits Die, Designer Rosette Bigz XL die, Vintage Faceted Designer Buttons, Linen Thread, 1/8″ Very Vanilla Taffeta Ribbon.  Cherry Cobbler Scalloped Tulle Ribbon, Dazzling Diamonds, Large Basic Pearl, 2-1/2″ circle punch and 1-3/8″ circle punch, 1/8″ handheld circle punch.

Adhesive: Tombow Liquid Glue, Hot Glue Gun and 2-Way Glue Pen.

Let me know if you have any questions.  Thanks for looking.

Advertisements
1 Comment »

Catalog Case – Christmas Cheer Snowflake

This is a case from the SU Holiday Catalog on page 14.  Thanks to Linda Heller for sharing her tips, like running the snowflake die through the Big Shot three times, then take one of the large snowflakes, then clip off the round tips.

Card Size 5″ x 5″ Click on pic to see more details

Inside of card, sitting on top of a decorated envelope

Supplies:

Stamp Sets: Distressed Dots, Sweet Essentials and Delightful Dozen

Paper: Gumball Green, Certainly Celery, Whisper White, Silver Glimmer Paper and Polka Dot Parade Real Red DSP

Ink:  Gumball Green

Accessories:  Basic Pearls, Cherry Cobbler Twine, Bigz Snow Flurry Die and 3 1/2: Circle Die, Dimensionals

2 Comments »

%d bloggers like this: